10 Best Multiplexer 16 In The Us - Black Friday 2024
Best Choice1
Adafruit16-Channel 12-bit PWM Servo Driver with I2C Interface
Main highlights- i2c-controlled PWM driver with a built in clock
- Solder jumpers for the 6 address select pins
- Polarity protection on the terminal block input
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
9.8Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
DEVMODEVMO 2PCS CD74HC4067 16 Channel Analog Digital Multiplexer MUX Breakout Board CD74HC4067 Precise Module Compatible with Ar-duino DIY
Main highlights- ★Wide operating temperature range: -55C to 125C
- ★This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- ★Package Includes: 1PCS 16 Ch. Mulitplexer,2PCS Header Pins as shown above
- ★6ns break-before-make @ 4.5V,"On" resistance: 70 Ohms @ 4.5V
- ★2V to 6V operation
9.7Exceptional
View offer on:
Show more
3
DORHEA12Pcs CD74HC4067 16-Channel Analog Digital Multiplexer MUX Breakout Board Module CD74HC4067 CMOS Precise Module Compatible with DIY
Main highlights- To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins.
- The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
- Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to.
- It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.If you want two-way communications,you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C,SPI,etc.
- CD74HC4067 board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer, use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels; Analog output: DIG; Channel control: S0-S3
9.6Exceptional
View offer on:
Show more
4
DAOKAIDAOKAI 10PCS CD74HC4067 High Speed CMOS Precise Analog Multiplexer 16-Channel Analog Digital Multiplexer MUX Breakout Board Module
Main highlights- 🔘[Product]This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. It works with both digital and analog signals, and the connection works in both directions
- 🔘[Package includes]You will get 10 x 16-Channel Analog Digital Multiplexer Breakout Board Module
- 🔘[Multi-device transfer]Since the mux/demux also works with digital signals, you can use it to pipe TTL level serial data to or from multiple devices.
- 🔘[Internal switch]The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching.
- 🔘[Function] Use one ADC to collect 16 analog signals. 16-channel analog signal switch using CD74HC4067
9.5Excellent
View offer on:
Show more
5
UMLIFE6pcs CD74HC4067 CMOS 16 Channel 16 CH Digital Analog Multiplexer Breakout Module for Arduino
Main highlights- Wide operating temperature range: -55C to 125C
- Use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels.
- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- IT can be used the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- Analog output: DIG;Channel control: S0-S3
9.2Excellent
View offer on:
Show more
6
QCCANQCCAN 12PCS CD74HC4067 16-Channel Analog Digital Multiplexer Breakout Board Module 2V-6V
Main highlights- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.
- Function: Use 16 ADCs to collect 16 analog signals. Use the CD74HC4067 16-channel analog signal switch.
- A method for controlling the motor, lights, LED, DC motors, micro-pumps, solenoid valves, etc., very convenient.
- .Analog Input: C0-C15 16 channels; Analog output: DIG; Channel Control: S0-S3
9.1Excellent
View offer on:
Show more
7
ACEIRMCACEIRMC 10pcs CD74HC4067 16-Channel Analog Digital Multiplexer Breakout Board Module for Arduino 2V-6V Microcontroller 16 Device RX Lines
Main highlights- To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want. This allows you to connect up to 16 sensors to your system using only 5 pins!
- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067. This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx)
- This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
- It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction.
- Analog output: DIG;Channel control: S0-S3
9.0Excellent
View offer on:
Show more
8
BridgoldBridgold 10pcs 74HC4051 74HC 8-Channel Analog multiplexer, Signal Splitter,16-DIP
Main highlights- Wide analog input voltage range: ± 5 V
- Typical “break before make” built in
- The products have been strictly screened, with stable performance and reliable data output.
- Output capability: non-standard
- Logic level translation: to enable 5 V logic to communicate with ± 5 V analog signals
8.9Very Good
View offer on:
Show more
9
PAMEENCOSPAMEENCOS 10 pcs CD74HC4067 High-Speed CMOS 16-Channel Analog Multiplexer for Analog Digital
Main highlights- Use one ADC to collect 16 analog signals. 16-channel analog signal switch using CD74HC4067. Analog signal input: C0-C15 16 channels. Analog output: DIG. Channel control: S0-S3.
- The internal switches are bidirectional, support voltages between ground and VCC, have low “on” resistance and low “off” leakage, and to prevent crosstalk, perform “break-before-make” switching. The board also breaks out the chip’s “enable” pin, which when driven high, will completely disconnect the common pin (all switches “off”).
- Since the mux/demux also works with digital signals, you can use it to pipe TTL-level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices. If you want two-way communications, you can add a second board to route your microcontroller’s TX line to 16 device’s RX lines. By using multiple boards, you can create similar arrangements for I2C, SPI.
- It works with both digital and analog signals (the voltage can’t be higher than VCC), and the connections function in either direction. To control it, connect 4 digital outputs to the chip’s address select pins (S0-S3), and send it the binary address of the channel you want (see the datasheet for details). This allows you to connect up to 16 sensors to your system using only 5 pins!
- 2V to 6V operation, 'On' resistance: 70 Ohms @ 4.5V, 6ns break-before-make @ 4.5V
8.7Very Good
View offer on:
Show more
10
EC BuyingEC Buying 3Pcs 16 Channel CD74HC4067 Digital Analog Multiplexer Breakout Module 16 CH CMOS ADC Module Analog/Digital for Arduino
Main highlights- With a wide operating temperature range of -55C to 125C, the 16 CH CMOS ADC Module Analog/Digital for Arduino is suitable for various environmental conditions, providing reliability and durability
- Utilize the 6ns break-before-make switching of the CD74HC4067 to prevent crosstalk and ensure smooth data transmission, enhancing the performance of your projects
- The low “on” resistance of 70 Ohms @ 4.5V in the CD74HC4067 ensures efficient signal transmission, making it an essential component for your electronic setups
- Easily connect up to 16 sensors to your system using only 5 pins with the 16 channel CD74HC4067 Digital Analog Multiplexer Breakout Module
- Control digital and analog signals bidirectionally with the high-speed CMOS ADC Module Analog/Digital for Arduino, allowing for versatile use in your electronic designs
8.5Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for multiplexer 16
