10 Best Xgecu T56 Programmer In The Us - Black Friday 2024
Best Choice1
ICTOLTOLXgecu T56 EPROM Programmer 17 Adapters Xgecu TL866II Plus T48 top Version 56 Pin Drivers ISP Support 33000+ ISP IC Chip PIC NAND Flash EMMC IC Bios AVR EPROM MCU SPI Nor Tester Clip Socket
Main highlights- Support Lower Voltage Chips:T56 programmer can directly support a minimum of 1.20V programming voltage, some non-technical sellers configure the T56 programmer with a 1.8V adapter, which is a completely useless accessory and a waste of money.
- Speed Faster:T56 programmer meets or exceeds the speed of most specialised programmers. Stability and reliability of the programmer are the most important.
- Product Support:XGecu T56 Programmer support for Nor Flash / NAND Flash / EMMC TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA2222 / BGA222222 / BGA22222 1.24. 25/26/93 serial EEPROM, 27/28/29/36/37/39/49/50 EPROM, Paged EPROM, Flash memory (NOR, NAND, SPI NAND, EMMC, NVRAM, SRAM, CPLD (GAL), etc. NAND EMMC supports maximum capacity up to 256G.
- Product Introduction:T56 programmer parameters (1). 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB 2.0 HS 480MHz transmission (2). 56-pin powerful pindrivers IO design. All pins have a maximum operating frequency of 50 MHz and high reliability. (3) Stable and reliable 8-pin in-circuit programming ISP interface, the wire length is more than 30 cm, and it can communicate reliably at 25 MHZ. 25 series / EMMC in-circuit programming with a maximum clock frequency of 40MHZ-50MHZ.
- Please Note:Before buying, make sure the chip models you want to program are in the support list. Please contact us for checking.
9.9Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
MORIENZIXgecu T56 EEPROM Programmer 17 Adapters Xgecu T48 top Version ISP IC Chip PIC NAND Flash EMMC IC Bios AVR EPROM MCU SPI Nor Tester Clip Socket
Main highlights- Support Lower Voltage Chips:T56 programmer can directly support a minimum of 1.20V programming voltage, some non-technical sellers configure the T56 programmer with a 1.8V adapter, It don't need extra adapter
- Product Support:XGecu T56 Programmer support for Nor Flash / NAND Flash / EMMC TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA2222 / BGA222222 / BGA22222 1.24. 25/26/93 serial EEPROM, 27/28/29/36/37/39/49/50 EPROM, Paged EPROM, Flash memory (NOR, NAND, SPI NAND, EMMC, NVRAM, SRAM, CPLD (GAL), etc. NAND EMMC supports maximum capacity up to 256G.
- Product Introduction:T56 programmer parameters (1). 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB 2.0 HS 480MHz transmission (2). 56-pin powerful pindrivers IO design. All pins have a maximum operating frequency of 50 MHz and high reliability. (3) Stable and reliable 8-pin in-circuit programming ISP interface, the wire length is more than 30 cm, and it can communicate reliably at 25 MHZ. 25 series / EMMC in-circuit programming with a maximum clock frequency of 40MHZ-50MHZ.
- Note: before you buy ,you can download the software or contact us to check the programmer whether support the chip typle,which adapter it need, then choose the adapter kit you need,thanks
9.7Exceptional
View offer on:
Show more
3
XGecuXGecu T56 Universal USB Programmer 56 Pin Drivers Support 33000+ ICS for Nor Flash/NAND Flash/Emmc/ Tsop32/Tsop40/Tsop48/Tsop56+9 Adapters+ Soic 8 Test Clip
Main highlights- 5. The shell size: 12.9CM*8.5CM*3CM, it's small and easily portable. Cool appearance, low power consumption, excellent work stability. Support simultaneously working with 4 Programmers on each computer.
- 4. User-friendly software interface, supports multi-language (English, Chinese, Russian, Polish, German, Spanish, Portuguese, Turkish), it can automatically identify the operating system to install and run under XP/WIN 2003/WIN 2008/WIN VISTA /WIN7/WIN8/WIN10 (32BIit/64Bit).
- 3. Design focused on high-capacity memories programming. IC supported 20000+ for Nor Flash / NAND Flash / EMMC / TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221, please check Device List in details. Remarkable performance, 56-pins powerful pindrivers, ultra fast programming speed, program 2 GB eMMC NAND Flash in less than 160 sec. Reading EMMC speed: 14MB/s-45MB/s, it is 2-5 times faster than similar programmers.
- 2.No adapter required for any DIL devices. All programming adapters are fully open source. No encryption adapter is used. You can buy a universal adapter, or make your own adapters. This feature will bring customers incomparable convenience, it will save you a lot of money. This package includes SOP28-DIP28 300mil, SOP20-DIP20 200mil, SOP16-DIP16 150mil, TSOP32/40/48/56 ZIF adapter (SN-ADP-056-0.5), PLCC adapter kit and Soic8 test clip.
- 1.XGecu T56 programmer is a 56-pin full-drive programmer, which is common to all chips in the same package within 56 pins. Each adapter has a clear prompt in the software, the pin check function is located to the pin number of the chip. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
9.6Exceptional
View offer on:
Show more
4
ACEIRMCACEIRMC T56 Universal USB Programmer 56 Pin Drivers Support 33000 ICS for Nor Flash/NAND Flash/Emmc/ Tsop32/Tsop40/Tsop48/Tsop56+9 Adapters (T56 + 9 Adapter)
Main highlights- User-friendly software interface, supports multi-language (English, Chinese, Russian, Polish, German, Spanish, Portuguese, Turkish), it can automatically identify the operating system to install and run under XP/WIN 2003/WIN 2008/WIN VISTA /WIN7/WIN8/WIN10 (32BIit/64Bit).
- T56 programmer is a 56-pin full-drive programmer, which is common to all chips in the same package within 56 pins. Each adapter has a clear prompt in the software, the pin check function is located to the pin number of the chip. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
- T56 Universal USB Programmer 56 Pin Drivers Support 33000+ ICS for Nor Flash/NAND Flash/Emmc/ Tsop32/Tsop40/Tsop48/Tsop56+9 Adapters+ Soic 8 Test Clip
- No adapter required for any DIL devices. All programming adapters are fully open source. No encryption adapter is used. You can buy a universal adapter, or make your own adapters. This feature will bring customers incomparable convenience, it will save you a lot of money. This package includes SOP28-DIP28 300mil, SOP20-DIP20 200mil, SOP16-DIP16 150mil, TSOP32/40/48/56 ZIF adapter (SN-ADP-056-0.5), PLCC adapter kit and Soic8 test clip.
- Design focused on high-capacity memories programming. IC supported 20000+ for Nor Flash / NAND Flash / EMMC / TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221, please check Device List in details. Remarkable performance, 56-pins powerful pindrivers, ultra fast programming speed, program 2 GB eMMC NAND Flash in less than 160 sec. Reading EMMC speed: 14MB/s-45MB/s, it is 2-5 times faster than similar programmers.
9.5Excellent
View offer on:
Show more
5
XGecuXGecu T56 Universal Programmer 56 Pin Drivers Support 34000+ ICS for Nor Flash/NAND Flash/EMMC TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221
Main highlights- 5. 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB2.0 HS 480MHZ transmission. 56-pins powerful pindrivers IO design. Stable and reliable 8-Pins in-circuit programming ISP interface. VCC voltage 1.2-6.5V 64 levels adjustable. VPP voltage 6.5-25V 64 levels adjustable. IO communication signal voltage continuously adjustable 1.2V-3.6V. VCC 120MA-320MA overcurrent protection continuously adjustable. VPP 120MA overcurrent protection. Power consumption: 5V <500MA.
- 4.User-friendly software interface, supports multi-language (English, Chinese, Russian, Polish, German, Spanish, Portuguese, Turkish), it can automatically identify the operating system to install and run under XP/WIN 2003/WIN 2008/WIN VISTA /WIN7/WIN8/WIN10 (32BIit/64Bit). The shell size: 12.9CM*8.5CM*3CM, it's small and easily portable. Cool appearance, low power consumption, excellent work stability. Support simultaneously working with 4 Programmers on each computer.
- 3.Design focused on high-capacity memories programming. IC supported 20000+ for Nor Flash / NAND Flash / EMMC / TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221, please check Device List in details. Remarkable performance, 56-pins powerful pindrivers, ultra fast programming speed, program 2 GB eMMC NAND Flash in less than 160 sec. Reading EMMC speed: 14MB/s-45MB/s, it is 2-5 times faster than similar programmers.
- 2.No adapter required for any DIL devices. All programming adapters are fully open source. No encryption adapter is used. You can buy a universal adapter, or make your own adapters. This feature will bring customers incomparable convenience, it will save you a lot of money. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
- 1.XGecu T56 programmer is a 56-pin full-drive programmer, which is common to all chips in the same package within 56 pins. Each adapter has a clear prompt in the software, the pin check function is located to the pin number of the chip. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
9.3Excellent
View offer on:
Show more
6
XGecuXGecu T48 [TL866-3G] Programmer TL866CS TL866II Replacement Support 31000+ ICS for EPROM/MCU/SPI/Nor/NAND Flash/EMMC + 13 Parts
Main highlights- 6. Package include: One T48 Programmer; One USB cable; One Warranty Card; One SOIC8 ZIF adapter, Body width 150 mil (3.9mm-4.1mm) One SOIC8-DIP8 ZIF adapter, Body width 200-209 mil (5-6mm) One TSSOP8 ZIF adapter, Body width 170 mil One SOIC28-DIP28 ZIF adapter, Body width 300mil One SOIC 8-16 SMD adapter One TSSOP8 and SOP16 SMD adapter One ANDK SOIC SOP8 IC test clip/ IC clamp One PLCC44-DIP40 2-in-1 adapter One PLCC32-DIP32 adapter One PLCC32-DIP28 adapter (support low voltage IC) One PLCC28-DIP24 adapter One PLCC20-DIP20 adapter One PLCC IC extractor
- 5. USB2.0 HS 480MHZ; Volume: 10X6.5X2.8 cm; 16 channel ISP, total 56-channel dedicated IO; VCC voltage 1.8-6.5V 64 levels adjustable, VPP voltage 9V-25V 64 levels adjustable; Power consumption: 5V <500MA. Self-test function, self-test each pin of VPP/VCC/GND/IO; Suitable for developers and maintenance personnel, can do small batch production for high capacity chips, support simultaneously working with 4 Programmers on each computer.
- 4. Production of high-density SMD technology, a unified user interface, easy to use, fully functional, reliable program running of application software, ultra-small (size is almost the same as TL866II), code-runs much faster, support multilanguage menu (English, Chinese, Russian, Polish, German, Spanish, Portuguese, Turkish, Czech, Italian), it can automatically identify the operating system to install and run under Windows XP,2003,2008,Vista Win7 WIN8 WIN10 WIN11.
- 3. Please note: the package don't include CD, you can download documents as below: www.mediafire.com/folder/hfg5kfj7euw5j/xgecu; Please check the support list for the details: www.xgecu.com/MiniPro/T48_List.txt; Before buying, make sure the models you want to program are in the support list. The new software will be improved future, so please contact us to resolve at first if any questions and suggestions.
- 2. Programming speed much faster. For example, for W25Q80, 3.5s+0.3s(Program+Verify) (30MHZ); for SPI NOR FLASH 25Q128, 30s+5.4s(P+V) (30MHZ); for P_NAND 29F1G08AB, 27s+17s(P+V); for P_NOR FLASH EN29LV320 TSOP48, 24s+1.9s(P+V)...... Support EMMC/EMCP; P-NAND; SPI NAND FLASH; GAL PLD; MCU: 51/PIC/AVR; 27/28/29/39/49/50; 24/25/45/93/95; 74 Series Logic IC Visual Test
- 1. With 40-pin industrial high-quality ZIF Socket (Pluggable/replaceable), newest model T48 (TL866-3G) programmer is the improvement of TL866II Plus programmer. Based on 32-bit MCU with 120MHZ and 4-layer PCB design, this professional T48 programmer support high-capacity NAND EMMC up to 256GB and programming speed is much higher. Suppport high-voltage chips, such as 27Cxxx series, VPP Maximum up to 25V, that is what TL866II cannot achieve.
9.0Excellent
View offer on:
Show more
7
ICTOLTOLXgecu TL866II Plus Upgraded Xgecu T48 programmer 19 Adapter Socket IC Tl866 Nand Nor Flash 24 93 25 Mcu Bios EPROM AVR Chip Eprom programmer
9.9 worth the money9.9 Simple to use9.7 FlexibilityWhy we love it
Versatile unit supports various chip types and sizes.
Fast programming speeds save time on projects.
Compatible with multiple Windows operating systems.
8.9Very Good
View offer on:
Show more
8
MORIENZIXgecu TL866II Plus Upgraded Xgecu T48 Programmer 24 Adapter t48 eprom Programmer TL866-3G IC Bios AVR MCU SPI Nor NAND Flash EMMC Clip Socket
Main highlights- T48 (TL866-3G) programmer is the improvement of TL866II Plus programmer,With 40-pin industrial high-quality ZIF Socket (Pluggable/replaceable),.Based on 32-bit MCU with 120MHZ and 4-layer PCB design.
- Support operating systems: Windows XP,2003,2008,Vista Win7 WIN8 WIN10 WIN11
- Support high-capacity NAND EMMC up to 256GB and programming speed is much higher. Suppport high-voltage chips, such as 27Cxxx series, VPP Maximum up to 25V, that is what TL866II cannot achieve.n do small batch production for high capacity chips.
- Self test function, self test each pin of VPP/VCC/GND/IO,suitable for developers and maintenance personnel
- Before buying, please contact us for checking the chip models you want to program whether this programmer support or not. The new software will be improved future,.
8.8Very Good
View offer on:
Show more
9
XGecuXGecu T56 Universal Programmer 56 Pin Drivers + PLCC Adapter kit PLCC20/28/32/44 to DIP20/24/28/32/44
Main highlights- 5. 32-bit MCU 200MHZ + Xilinx SP6 FPGA structure, USB2.0 HS 480MHZ transmission. 56-pins powerful pindrivers IO design. Stable and reliable 8-Pins in-circuit programming ISP interface. VCC voltage 1.2-6.5V 64 levels adjustable. VPP voltage 6.5-25V 64 levels adjustable. IO communication signal voltage continuously adjustable 1.2V-3.6V. VCC 120MA-320MA overcurrent protection continuously adjustable. VPP 120MA overcurrent protection. Power consumption: 5V less than 500MA.
- 4.User-friendly software interface, supports multi-language (English, Chinese, Russian, Polish, German, Spanish, Portuguese, Turkish), it can automatically identify the operating system to install and run under XP/WIN 2003/WIN 2008/WIN VISTA /WIN7/WIN8/WIN10 (32BIit/64Bit). The shell size: 12.9CM*8.5CM*3CM, it's small and easily portable. Cool appearance, low power consumption, excellent work stability. Support simultaneously working with 4 Programmers on each computer.
- 3.Design focused on high-capacity memories programming. IC supported 20000+ for Nor Flash / NAND Flash / EMMC / TSOP48 / TSOP56 / BGA48 / BGA63 / BGA64 / BGA100 / BGA153 / BGA162 / BGA169 / BGA221, please check Device List in details. Remarkable performance, 56-pins powerful pindrivers, ultra fast programming speed, program 2 GB eMMC NAND Flash in less than 160 sec. Reading EMMC speed: 14MB/s-45MB/s, it is 2-5 times faster than similar programmers.
- 2.No adapter required for any DIL devices. All programming adapters are fully open source. No encryption adapter is used. You can buy a universal adapter, or make your own adapters. This feature will bring customers incomparable convenience, it will save you a lot of money. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
- 1.XGecu T56 programmer is a 56-pin full-drive programmer, which is common to all chips in the same package within 56 pins. Each adapter has a clear prompt in the software, the pin check function is located to the pin number of the chip. Open source programming adapter, for example, TSOP32/TSOP40/TSOP48/TSOP56, PLCC32, PLCC44, TQFP44, BGA48, BGA63, BGA64, SOP44, TQFP32 and so on
8.5Good
View offer on:
Show more
10
MORIENZIXgecu T48 Programmer 19 Adapter t48 eprom Programmer Xgecu TL866II Plus Upgraded Reader Writer TL866-3G IC Bios AVR MCU SPI Nor NAND Flash EMMC Clip Socket
Main highlights- T48 (TL866-3G) programmer is the improvement of TL866II Plus programmer,With 40-pin industrial high-quality ZIF Socket (Pluggable/replaceable),.Based on 32-bit MCU with 120MHZ and 4-layer PCB design.
- Support operating systems: Windows XP,2003,2008,Vista Win7 WIN8 WIN10 WIN11
- Support high-capacity NAND EMMC up to 256GB and programming speed is much higher. Suppport high-voltage chips, such as 27Cxxx series, VPP Maximum up to 25V, that is what TL866II cannot achieve.n do small batch production for high capacity chips.
- Self test function, self test each pin of VPP/VCC/GND/IO,suitable for developers and maintenance personnel
- Before buying, please contact us for checking the chip models you want to program whether this programmer support or not. The new software will be improved future
8.4Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for xgecu t56 programmer
