10 Best Servo Driver I2c Interface Pca9685 for Arduino In The Us - Black Friday 2024
Best Choice1
AdafruitAdafruit (PID 815 16-Channel 12-bit PWM/Servo Driver - I2C Interface - PCA9685
Main highlights- This product comes with a fully tested and assembled breakout as well as 4 pieces of 3x4 male straight header (for servo/LED plugs), a 2-pin terminal block (for power) and a piece of 6-pin 0.1" header (to plug into a breadboard). A little light soldering will be required to assemble and customize the board by attaching the desired headers but it is a 15 minute task that even a beginner can do.
- Some soldering required
- PCA9685 PWM driver
- Includes Breakout and headers
- 5V compliant
9.9Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
Shutao5Pcs PCA9685 16 Channel 12-bit PWM Servo Motor Driver Board I2C interface Controller PCA9685 module Raspberry Pi Shield Module Servo Shield
Main highlights- This is a PCA9685 16 channel I2C communication, built-in PWM driver and a clock.
- PCA9685 module 2-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz.
- PCA9685 IIC module 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V+ forward voltage
- 3 pin connectors in 4 groups, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 adjacent ones on 0.1"-hole female headers.
- 16 channel PWM module supports using only two pins to control 16 free-running PWM outputs , the 6 address selection pin allows you to hook 62 driver boards on a single I2C bus, with a total of 992 PWM outputs.
9.8Exceptional
View offer on:
Show more
3
HiLetgoHiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
Main highlights- Voltage: DC5-10V power supply
- The PCA9685 chip is wrapped in the center of the board
- Communication Interface: IIC
- All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
- 16-way steering gear control
9.7Exceptional
View offer on:
Show more
4
VKLSVANVKLSVAN 3PCS PCA9685 16 CH Channel PWM Servo Motor Driver Board Controller 12 bit IIC Interface Module for Arduino or Raspberry pi
Main highlights- Supports using only two pins to control 16 free-running PWM outputs ¨C you can even chain up 62 breakouts to control up to 992 PWM outputs.
- PCA9685 Contains an I2C-controlled PWM driver with a built-in clock; Power supply voltage is DC5-10V
- It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages).
- 3 pin connectors in groups of 4, so you can plug in 16 servos at one time .
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.6Exceptional
View offer on:
Show more
5
AlinanAlinan 4pcs PCA9685 16 Channel 12 Bit PWM Servo Motor Driver Board I2C IIC Module IIC Interface
Main highlights- 【The PCA9685 Chip】: The PCA9685 chip is wrapped in the center of the board, PCA9685 contain an I2C-controlled PWM driver with a built-in clock. 16 Channel PWM/Servo Driver IIC interface-PCA9685 for shield module servo shield
- 【Specification】: Voltage: DC5-10V power supply, Frequency: 40-1000Hz; Channel number: 16 channel; Resolution: 12 bit; Voltage: DC 5-10V, Size: Approx. 60 x 25 mm/ 2.36 x 0.98 inch
- 【Easy to Use】: supports using only 2 pins (6 address select pins) to control 16 free-running PWM outputs, you can control the 16 way servo motor, so you can wire up to 62 of these on a single I2C bus to control up to 992 PWM outputs. 3 pin connectors in groups of 4, so you can plug in 16 servos at one time
- 【5V Compliant】: It is 5V compliant, which means you can control it from a 3.3V micro controller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
- ★All PWM output lines have a 220 ohm series resistor protection and can easily drive LED. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.5Excellent
View offer on:
Show more
6
HUAREWHUAREW PCA9685 16 Channel PWM Servo Driver Board 12 bit IIC Interface Module Compatible with Arduino and Raspberry Pi (2pcs)
Main highlights- Using only two pins, control 16 free-running PWM, so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs
- PCA9685 contain an I2C communication PWM driver with a built in clock, so you do not need to continuously send it signal tying up your microcontroller
- PCA9685 IIC module 5V compliant, you can also control it from a 3.3V microcontroller and still safely drive up to 6V outputs
- Green power indicator lamp, 3 pin connectors in groups of 4, so you can plug in 16 servos at one time(servo motor plug slightly wider than 0.1 inch)
- 12 bit resolution for each output for servos, that means about 4us resolution at 60Hz update rate
9.4Excellent
View offer on:
Show more
7
AITIAOAITIAO 3Pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Interface Module PCA9685 Controller Module for Robot Raspberry pi
Main highlights- Supports using only two pins to control 16 free-running PWM outputs, you can even chain up 62 breakouts to control up to 992 PWM outputs.
- PCA9685 Servo Driver: Power supply voltage is DC5-10V; Communication Interface: IIC; PCA9685 Contains an I2C-controlled PWM driver with a built-in clock.
- PCA9685 Driver Controller is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs(it is good when you want to control white or blue LEDs with a 3.4V+ forward voltage)
- 3 pin connectors in 4 groups, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 adjacent ones on 0.1"-hole female headers.
- 12-bit resolution for each output,for servos, that means about 4us resolution at an update rate of 60Hz.
9.3Excellent
View offer on:
Show more
8
SunFounderSunFounder PCA9685 16 Channel 12 bit PWM Servo Driver for Arduino and Raspberry Pi
Main highlights- Support using only two pins to control 16 free-running PWM outputs – you can even chain up 62 breakouts to control up to 992 PWM outputs
- Contain an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running
- 5V compliant, which means you can control it from a 3.3V microcontroller (this is good when you want to control white or blue LEDs with 3.4+ forward voltages)
- 3 pin connectors in groups of 4, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.2Excellent
View offer on:
Show more
9
Adafruit16-Channel 12-bit PWM Servo Driver with I2C Interface
Main highlights- i2c-controlled PWM driver with a built in clock
- Solder jumpers for the 6 address select pins
- Polarity protection on the terminal block input
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
9.1Excellent
View offer on:
Show more
10
AITRIPPCA9685 16 CH 12Bit PWM Servo Motor Driver Board Controller IIC Interface for Arduino Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+ and Robot (2pcs)
Main highlights- Supports using only two pins to control 16 free-running PWM outputs – you can even chain up 62 breakouts to control up to 992 PWM outputs.
- Contains an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running!
- 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs, which is good when you want to control white or blue LEDs with a 3.4V+ forward voltage
- 3 pin connectors in 4 groups, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 adjacent ones on 0.1"-hole female headers.
- 12-bit resolution for each output - for servos, that means about 4us resolution at an update rate of 60Hz.
8.9Very Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for servo driver i2c interface pca9685 for arduino
