10 Best Raspberry Pi Oled Display In The Us - Black Friday 2024
Best Choice1
waveshareWaveshare 1.51inch Transparent OLED 128×64 Resolution Compatible with Raspberry Pi 4B/3B+/3A+ Embedded Independent Driver Chip SPI/I2C Interfaces Light Blue Color Display
Main highlights- The program defaults to SPI mode. If you need to switch the mode, please modify DEV_Config.h. For details, please refer to the program description - bottom hardware interface - interface selection.
- Provide online user manual, please check the manual carefully before using!
- OLED transparent module, full viewing angle
- Comes with development resources (examples for Raspberry Pi/Arduino/STM32)
- Adopts 4-wire SPI and I2C interface, better compatibility, fast data rate
9.8Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
wavesharewaveshare 1.27inch RGB OLED Display Module 128×96 Resolution Screen, 262K RGB Colors SPI Interface 3.3V / 5V Operating Voltage, for Ardu/Raspberry Pi/STM32
Main highlights- SPI interface, 4-wire SPI, 3-wire SPI, minimizes required IO pins
- Resolution: 128(H)RGB x 96(V). Dimension: 25.708 × 19.28mm.
- Operating voltage: 3.3V / 5V. Embedded SSD1351 driver chip.
- Comes with online development resources (examples for Raspberry Pi/Arduino/STM32)
- 128×96 resolution OLED display, 262K colors, clear and colorful displaying effect
9.7Exceptional
View offer on:
Show more
3
wavesharewaveshare 1.5inch RGB OLED Display Module for Raspberry Pi/Jetson Nano/Arduino/STM32, 128x128 Pixels,16-bit High Color (65K Colors) SPI Interface
Main highlights- Viewing angle: >160°. Operating voltage: 3.3V / 5V. Dimension: 44.5 x 37 (mm).
- This is a general 1.5inch RGB OLED display module, 128x128 pixels, 16-bit high color (65K colors),clearly displays colorful images, with embedded controller, communicating via SPI interface.
- Driver: 1351. Interface: 4-wire SPI, 3-wire SPI. Display color: RGB, 65K colors. Resolution: 128x128.
- 128x128 high resolution, 65K colors, clearly displays colorful images. Supports 4-wire SPI OR 3-wire SPI interface, configured via onboard resistor.
9.5Excellent
View offer on:
Show more
4
HosyondHosyond 5 Pcs 0.91 Inch I2C IIC OLED Display Module OLED Screen DC 3.3V~5V Compatible with Arduino Raspberry PI (Blue Display Color)
Main highlights- Working power:3.3-5v, Operating temperature: -40 - 85 ℃.
- What will you get: there are 5 pieces OLED display module OLED display module for you.
- Resolution: 128 x 32 0.91 Inch OLED display, no need backlight, self-illumination, Display Color: White.
- Low power consumptio; SSD 1306 oled display; I2C oled display, IIC (I2C communications) simplifies connection.
- Compatible with Arduino nano, R3 board, Raspberry Pi 4B/3B+/3B/2B/Zero,ESP8266, ESP32, STM32, etc.
9.4Excellent
View offer on:
Show more
5
HosyondHosyond 5 Pcs 0.96 Inch OLED I2C IIC Display Module 12864 128x64 Pixel SSD1306 Mini Self-Luminous OLED Screen Board Compatible with Arduino Raspberry Pi(Blue and Yellow)
Main highlights- There are no fonts embedded in the OLED controller, users can create fonts through font generation software.
- No backlight is required, and the display unit can be self-luminous. It has ultra-high contrast, bright and clear dots, and it is easy to read even small fonts
- It compatibles with R3 board and Mega, Raspberry pi, 51 MCU, STIM 32, etc.
- Embedded Driver IC: SSD1306. Communication: I2C/IIC Interface, only need two I / O ports
- 0.96 inch,Resolution: 128 x 64, View angle: > 160°, Support voltage: 3.3V-5V DC, Power consumption: 0.04W during normal operation, full screen lit 0.08W
9.1Excellent
View offer on:
Show more
6
wavesharewaveshare 2.42inch OLED Display Module 128×64 Resolution for Raspberry Pi/forArduino/STM32/ESP32/Jetson Nano, with SSD1309 Driver Chip SPI / I2C Communication 3.3V / 5V, White Display Color
Main highlights- Ultra-narrow bezel, conpact size, with onboard voltage translator
- Compatible with Raspberry Pi, Arduino, STM32, ESP32, Jetson Nano, etc. Comes with online development resources.
- Adopts 4-wire SPI and I2C interfaces, better compatibility, fast data rate
- 3.3V / 5V Operating voltage; 4-wire SPI (default) / I2C Communication Interface
- 2.42inch OLED Display Module, Embedded SSD1309 driver chip, SPI / I2C Communicatio, White Display Color
9.0Excellent
View offer on:
Show more
7
iPistBitiPistBit 5 Pcs 0.91 Inch I2C OLED Display Module, 128x32 Pixel SSD1306 Luminous OLED Screen Board Compatible with Arduino Raspberry Pi ESP32 (Blue)
Main highlights- The module pins are soldered and housed in a small bag to prevent them from falling off during transportation.
- The OLED display module is compatible with Raspberry Pi, Beagle Bone Black, Arduino Nano, UNO, R3, Mega, 51 MCU, and STM 32.
- The I2c OLED display module uses an SSD1306 embedded driver IC and communicates via the I2C/IIC interface, requiring only two I/O ports.
- Raspberry Pi screen module does not require a backlight and has an ultra-high contrast ratio, making small fonts clear and easy to read. There are no embedded fonts in the module, users can create fonts using font generation software.
- 0.91 inch OLED display with a resolution of 128 x 32 and a viewing angle greater than 160°. It supports a voltage range from 3.3V to 5V DC, with a normal operating power consumption of 0.04W and a power consumption of 0.06W when the screen is fully lit.
8.9Very Good
View offer on:
Show more
8
XYGStudyXYGStudy 2.23 inch OLED Display HAT for Raspberry Pi 2B/3B/4B/Zero/Zero W Jetson Nano 128×32 Pixels SPI/I2C Interface
Main highlights- Trying to add a control interface for your Pi? This compact display would be the ideal choice.
- This is an OLED display HAT for Raspberry Pi, 2.23inch diagonal, 128×32 pixels, with embedded SSD1305 driver, communicating via SPI or I2C interface.
- Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
- Part Number: 2.23inch OLED HAT
- 2.23inch OLED display HAT for Raspberry Pi, 128×32 pixels, SPI/I2C interface
8.6Very Good
View offer on:
Show more
9
FriendaFrienda 10 Pieces I2C OLED Display Module OLED Display Screen Driver IIC I2C Tabellone Seriale con Display Auto-Luminoso Compatible with Arduino/Raspberry PI
Main highlights- Self-luminous design: the OLED display module is self-luminous, so that no backlight is required; It features high contrast, bright and crisp dots, which is convenient for you to read tiny fonts
- Product information: resolution is 128 x 64; View angle is more than 160 degrees; Supporting voltage is from 3.3V to 5V DC; Power consumption during normal operation is 0.04W, full screen lit is 0.08W
- Driver and communication: embedded driver IC; Communication is IIC/ I2C interface, only needs 2 I/O ports; Compatible with MMDVM, Pi-Star, and compatible with Raspberry pi
- Create fonts: there are no fonts embedded in the OLED controller, so users can use the font generation software to create the fonts
- Compatibility: blue and yellow, 0.96 inch OLED module is designed to display graphic information and text information directly on your microcontroller project; Compatible with Mega, Raspberry pi, 51 MCU, STIM 32, etc.
8.5Good
View offer on:
Show more
10
AITRIPAITRIP 10 Pieces 0.96 Inch OLED I2C IIC Display Module 12864 128x64 SSD1306 Mini Self-Luminous Display Board Compatible with Arduino/Raspberry PI -White
Main highlights- Embedded driver IC: Communication: I2C/IIC Interface, only need 2 I/O ports; Compatible with MMDVM, Pi-Star； Instructions : https://wiki.52pi.com/index.php?title=S-0005
- Applications: MP3, MP4, watch；Head-mounted displays；Meters and other intelligent instruments；IT is compatible with Arduino Mega, Raspberry pi, 51 MCU, STIM 32, etc
- 128 X 64 PIXELS:Needn't backlight, the display unit can self-luminous. It has Super High Contrast, bright and crisp dots, even tiny fonts quite readable.No embedded fonts inside the OLED controller, user can create the fonts through the font generation software.
- 0.96 inch,Resolution: 128 x 64, View angle: > 160°, Support voltage: 3.3V-5V DC；Power consumption: 0.04W during normal operation, full screen lit 0.08W
- 0.96 inch OLED module for showing graphical and textual information directly on your micro-controller projects；Embedded Driver IC: SSD1306. Communication: I2C/IIC Interface, only need two I / O ports
8.3Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for raspberry pi oled display
