10 Best Mv720 Relay Gps Tracker In The Us - Black Friday 2024
- Curious about how we select the top products for you? Explore How It Works
Lisle 60150 Relay Pro 12V and 24V Relay Tester, Factory
Main highlights- This eliminates the need for specific tester footprints or adapters
- Tests relays by simply clicking the test leads onto the relay terminal pins using a 12 or 24V DC power source
- Automatically determines how the relay coil and contacts are configured
- A straightforward relay tester that will easily and quickly test most 12 and 24 volt DC automotive relays
SinoTrack ST-907L 4G Vehicle Car GPS Tracker, Car Relay Anti Lost Alarm GPS Locator Real-Time Location Remote Control Cut Off Oil and Power Device for Car Motorcycle Truck Taxi, Support Platform
8.9 Battery Duration8.0 Tech Support8.0 PrecisionWhy we love it
Real time trackingCut engine remotelyTracking platform lifetimeDIYmalls BN-220 GPS Module TTL Dual GPS Glonass w/Flash NMEA-0183 9600bps 1Hz for Arduino RC FPV Drone Flight Control
Main highlights- bn220 gps has flash to save configuration, so you do not need to reset data next time when you use it. But bn220 gps doesn't have compass. If you need gps with flash and compass, please check bn-880 gps via "Visit the DIYmalls Store"
- When you use it for pi, there is no driver installation needed but you need to install software
- When you power up bn 220 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold start”. Once you’ve done it the first time, later when you restart bn220 GPS module, it will get a lock much faster.
- If you have any problem, please do as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
Beitian GPS Module with Antenna UAV Drone M10050 M9140 chip Ultra-Low Power GNSS Receiver for Track GPS BE-180 BK-180 BN-180 BE-220 BK-220 BN-220
Main highlights- With FLASH, the configuration can be changed, and the power will not be lost
- Update rate: 0.25Hz-18Hz,default 10Hz
- The red light, the PPS light, does not light up if it is not positioned; after 3D positioning, it starts to flash.
- Note: Please use the GPS module in an open place, the LED will flash after the satellite signal is found. Bad weather and indoor use will affect the accuracy of positioning.
- Not positioned, the light is off; after 3D positioning, the blue light flashes
Iot Relay - Enclosed High-Power Power Relay for Arduino, Raspberry Pi, PIC or WiFi, Relay Shield
Main highlights- Wires to your Arduino, Raspberry Pi, PIC, or other micro
- Takes the place of a relay board. Fully assembled and ready to use.
- Safe, Reliable Power Control
- One circuit, 4 outlets, 2x NC, 2x NO
- Includes surge supression, debounce, safety breaker
MakerFocus GT-U7 GPS Module Satellite Navigation Positioning GPS Receiver Drone Microcontroller Compatible with NEO-6M 51 Microcontroller STM32 Arduino UNO R3 with IPEX Antenna High Sensitivity
Main highlights- With a USB interface, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, the default distribution of active antenna, can be quickly positioned
- USB directly connected to the computer, That is, with the host computer-owned serial port function, no need for external serial module, send IPX interface active antenna
- Note: Please use the GT-U7 GPS module in an open place, the LED will flash after the satellite signal is found. Bad weather and indoor use will affect the accuracy of positioning
- MakerFocus Global positioning system (GPS)
- How to use the GPS module better, the link is obtained in the Product guides and documents, please download it before use
- GPS baud needs to be set to 9600 instead of 4800; PPS pin is not needed unless using the GPS to drive a hardware high precision clock; GT-U7 main module GPS module using the original UBLOX 7th generation chip, Software is compatible with NEO-6M. GT-U7 module, with high sensitivity, low power consumption, miniaturization, its extremely high tracking sensitivity greatly expanded its positioning of the coverage
HiLetgo 2pcs 12V 30A One Channel Relay Module Optocoupler Isolation High and Low Trigger 12V
Main highlights- With optocoupler isolation, strong drive capability, stable performance; trigger current 5mA.
- Friendly interface design, all interfaces can be directly connected through the terminal leads, very convenient.
- 5V 12V 24V 30A One Channel Relay Module Optocoupler Isolation High and Low Trigger
Geekstory BN-220 Dual GPS Glonass Module Navigation TTL Level 9600bps + GPS Passive Antenna for Arduino Raspberry Pi Pixhawk F3 CC3D Betaflight F4 Flight Control
Main highlights- When you use it for Raspberry Pi, there is no driver needed but you need to install software
- The TX LED flash means gps module output normally.The PPS LED flash means gps module locate your place
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
- BN-220 gps module has flash to save configuration, so you do not need to reset data next time when you use it. But it has no compass. If you need gps with flash and compass, please buy bn-880 from Geekstory
- BN 220 gps module documentation link cannot be displayed. If you need technical documentation, please click “Ask a question” to em-ail us
Black Friday Sale
Deal ends in
HrsMinSec