10 Best Channel Pwm In The Us - Black Friday 2024
Best Choice1
MakerFocusMakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Compatible with Raspberry Pi 4 3B+ 3B Zero/Zero W/Zero WH and Jetson Nano
Main highlights- Servo Motor Driver: You may have tried to control a robotic arm or a hexapod walker by using the Raspberry Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you.
- Raspberry Pi connectivity, compatible with Raspberry Pi 4 3B+ 3B 2B+ 2B Zero/Zero W/Zero WH and Jetson Nano.
- Note: The Raspberry Pi and Servo in the photo are not included
- Note: 1.If you only connect 5V power supply to USB interface, servo cannot be driven; 2.You should connect higher power supply for higher-power servo; 3.Make sure servo are connected properly, otherwise they will not move.
- I2C controlled, using only 2 pins; Up to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales); Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminal.
9.9Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
GIDERWEL20% OffGIDERWEL 4 Channel DMX Decoder RGBW PWM DMX512 Dimmer Driver RGBW LED Strip Light Controller Input 12V-24V DC
Main highlights- The DMX address can be set through dip switch,And You could connect with DMX digital console to achieve RGB dimming functions;
- Receives standard DMX 512/1990 digital control signal and transformrd it into PWM signal to adjust LED Lights;
- Input Automatically adapt to DC12V-24V,And Output Max power load:240W(12V);480W (24V)
- High Power Output Max 20A For 5A Each Channel,Use for LED strip,LED module,LED light.
- Easy Use for 15 modes and 30 steps speeds for your options;signal interfaces XLR-3 and RJ45;
9.6Exceptional
View offer on:
Show more
3
HiLetgoHiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
Main highlights- Voltage: DC5-10V power supply
- The PCA9685 chip is wrapped in the center of the board
- Communication Interface: IIC
- All PWM output lines have a 220 ohm series resistor protection and can easily drive LED.
- 16-way steering gear control
9.5Excellent
View offer on:
Show more
4
Adafruit16-Channel 12-bit PWM Servo Driver with I2C Interface
Main highlights- i2c-controlled PWM driver with a built in clock
- Solder jumpers for the 6 address select pins
- Polarity protection on the terminal block input
- 3 pin connectors in groups of 4 so you can plug in 16 servos at once
- 220 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial
9.4Excellent
View offer on:
Show more
5
HUAREWHUAREW PCA9685 16 Channel PWM Servo Driver Board 12 bit IIC Interface Module Compatible with Arduino and Raspberry Pi (2pcs)
Main highlights- Using only two pins, control 16 free-running PWM, so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs
- PCA9685 contain an I2C communication PWM driver with a built in clock, so you do not need to continuously send it signal tying up your microcontroller
- PCA9685 IIC module 5V compliant, you can also control it from a 3.3V microcontroller and still safely drive up to 6V outputs
- Green power indicator lamp, 3 pin connectors in groups of 4, so you can plug in 16 servos at one time(servo motor plug slightly wider than 0.1 inch)
- 12 bit resolution for each output for servos, that means about 4us resolution at 60Hz update rate
9.3Excellent
View offer on:
Show more
6
VKLSVANVKLSVAN 3PCS PCA9685 16 CH Channel PWM Servo Motor Driver Board Controller 12 bit IIC Interface Module for Arduino or Raspberry pi
Main highlights- Supports using only two pins to control 16 free-running PWM outputs ¨C you can even chain up 62 breakouts to control up to 992 PWM outputs.
- PCA9685 Contains an I2C-controlled PWM driver with a built-in clock; Power supply voltage is DC5-10V
- It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages).
- 3 pin connectors in groups of 4, so you can plug in 16 servos at one time .
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.2Excellent
View offer on:
Show more
7
SunFounderSunFounder PCA9685 16 Channel 12 bit PWM Servo Driver for Arduino and Raspberry Pi
Main highlights- Support using only two pins to control 16 free-running PWM outputs – you can even chain up 62 breakouts to control up to 992 PWM outputs
- Contain an I2C-controlled PWM driver with a built-in clock. It means, unlike the TLC5940 family, you do not need to continuously send it signals tying up your microcontroller; it's completely free running
- 5V compliant, which means you can control it from a 3.3V microcontroller (this is good when you want to control white or blue LEDs with 3.4+ forward voltages)
- 3 pin connectors in groups of 4, so you can plug in 16 servos at one time (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.1Excellent
View offer on:
Show more
8
AlinanAlinan 4pcs PCA9685 16 Channel 12 Bit PWM Servo Motor Driver Board I2C IIC Module IIC Interface
Main highlights- 【The PCA9685 Chip】: The PCA9685 chip is wrapped in the center of the board, PCA9685 contain an I2C-controlled PWM driver with a built-in clock. 16 Channel PWM/Servo Driver IIC interface-PCA9685 for shield module servo shield
- 【Specification】: Voltage: DC5-10V power supply, Frequency: 40-1000Hz; Channel number: 16 channel; Resolution: 12 bit; Voltage: DC 5-10V, Size: Approx. 60 x 25 mm/ 2.36 x 0.98 inch
- 【Easy to Use】: supports using only 2 pins (6 address select pins) to control 16 free-running PWM outputs, you can control the 16 way servo motor, so you can wire up to 62 of these on a single I2C bus to control up to 992 PWM outputs. 3 pin connectors in groups of 4, so you can plug in 16 servos at one time
- 【5V Compliant】: It is 5V compliant, which means you can control it from a 3.3V micro controller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages)
- ★All PWM output lines have a 220 ohm series resistor protection and can easily drive LED. 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
9.0Excellent
View offer on:
Show more
9
ACEIRMCACEIRMC 3pcs 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi
Main highlights- PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
- It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs (this is good for when you want to control white or blue LEDs with 3.4+ forward voltages).
- 6 address select pins so you can wire up to 62 of these on a single i2c bus, a total of 992 outputs.
- 16 Channel PWM/Servo Driver IIC interface-PCA9685 for arduino or Raspberry pi shield module servo shield
- 12-bit resolution for each output - for servos, that means about 4us resolution at 60Hz update rate
8.9Very Good
View offer on:
Show more
10
ANMBESTANMBEST MOSFET Trigger Switch 4 Channel Drive Module 400W DC 3.7-27V 10A Large Power PWM Adjustment Electronic Switch Control Board
Main highlights- WIDELY APPLICATIONS: You can control the output of power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valves, etc., can input PWM, control motor speed, lamp brightness and so on.
- Supporting Multiple Signal Source Triggers: Can be connected microcontroller IO port, PLC interfaces, DC power, etc.
- PERFECT SUPPORT PWM: You can access the PWM signal, the signal frequency 0--20KHZ perfect support.
- Operating Voltage: DC 3V - 27V; The trigger source: digital high-low (DC3V - 20V); continuous current: 10A; power: 400W.
- High Reliability, High Availability: The drive module using high quality ultra-small optocoupler, with strong anti-interference ability, and stable performance, is complete isolation of input signal and output.
8.8Very Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for channel pwm
