10 Best Beitian Bn 180 Gps In The Us - Black Friday 2024
Best Choice1
GeekstoryGeekstory BN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation + BN-880 GPS Module U8 with Flash HMC5883L Compass + GPS Active Antenna Support GPS Glonass
Main highlights- This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd.
- The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place. This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps.
- Bn 880 gps module has flash to save configuration. So you do not need to reset next time when you use it. When you use it for Raspberry Pi, there is no driver needed but you need to install software.
- BN-880 is suitable for Open source flight controller, not for flight control with SCM, Bn 880 gps module is dual module compass, with and electronic compass IC HMC5883L.
- 1 PCS BN-180 GPS Module + 1 PCS BN-220 Dual GPS module
9.8Exceptional
View offer on:
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money2
GeekstoryGeekstory BN-880 GPS Module U8 with Flash HMC5883L Compass + GPS Active Antenna Support GPS Glonass Beidou Car Navigation for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller
Main highlights- When you use it for Raspberry Pi, there is no driver needed but you need to install software
- DIts data Level is TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
- Bn 880 gps module is dual module compass, with and electronic compass IC HMC5883L
- Bn 880 gps module has flash to save configuration. So you do not need to reset next time when you use it
- BN-880 is suitable for Open source flight controller, not for flight control with SCM
9.5Excellent
View offer on:
Show more
3
DIYmallsDIYmalls BN-180 GPS Glonass Module TTL NMEA-0183 1Hz 9600bps for Arduino Aircraft RC FPV Drone Flight Control
Main highlights- When you power up bn 180 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold start”. Once you’ve done it the first time, later when you restart bn180 GPS module, it will get a lock much faster.
- If you have any problem, please do as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
- BN180 GPS Module can be used with pi, esp32 development board, pc (driver required), drone flight controller etc.
- BN 180 gps doesn't have flash and compass. If you need it, please check bn-880 gps module via "Visit the DIYmalls Store"
9.3Excellent
View offer on:
Show more
4
DIYmallsDIYmalls BN-220 GPS Module TTL Dual GPS Glonass w/Flash NMEA-0183 9600bps 1Hz for Arduino RC FPV Drone Flight Control
Main highlights- bn220 gps has flash to save configuration, so you do not need to reset data next time when you use it. But bn220 gps doesn't have compass. If you need gps with flash and compass, please check bn-880 gps via "Visit the DIYmalls Store"
- When you use it for pi, there is no driver installation needed but you need to install software
- When you power up bn 220 GPS module the first time in a new location, it always takes longer to find satillites. This is referred to as “cold start”. Once you’ve done it the first time, later when you restart bn220 GPS module, it will get a lock much faster.
- If you have any problem, please do as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
9.0Excellent
View offer on:
Show more
5
GeekstoryBN-180 GPS Module UART TTL Dual Glonass GPS Car Navigation with GPS Antenna for Arduino Raspberry Pi Pixhawk Aircraft CC3D F3 Flight Controller Geekstory
Main highlights- What you will get: 1 X BN-180 GPS Module
- This BN-180 GPS Module does not have FLASH and cannot be saved. 72 Searching Channel Support Rate : 4800bps to 921600bps, Default 9600bps
- This BN-180 GPS Module can show your speed. When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd
- The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place
- Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
8.8Very Good
View offer on:
Show more
6
SoloGood2PCs Beitian BE220 M8N GPS Module Support GPS GLONASS BeiDou for RC Long Range FPV Racing Drone Airplane …
Main highlights- When it is used on Raspberry Pi, it is not necessary to install the driver, but the software must be installed
- The BE220 M8N GPS module has a flash memory function to save the configuration, which can help you do not need to reset the data next time you use it.
- Note: it does not have a compass
- If you have any questions, you can contact us at any time
- If the TX LED indicator flashes, it means that the BE220 M8N GPS module is operating normally, and the PPS LED indicator flashes to indicate that the GPS module has found your location
8.7Very Good
View offer on:
Show more
7
DIYmallsDIYmalls BN-880 GPS Module HMC5883 Compass Support GPS Glonass Beidou NMEA-0183 9600bps 1Hz for Arduino RC FPV Drone Flight Control
Main highlights- bn880 gps module is suitable for Open source flight controller, not for flight control with SCM. When you use it for r pi, there is no driver needed but you need to install software
- bn 880 gps module is dual module compass, with and electronic compass IC HMC5883L
- bn 880 gps module has flash to save configuration. So you do not need to reset data when you use it next time.
- You can check bn180 bn220 gps module via "Visit the DIYmalls Store"
- If you have any problem, please do as follow: click "DIYmalls"(you can find "Sold by DIYmalls" under Buy Now button), in the new page, click "Ask a question".
8.6Very Good
View offer on:
Show more
8
BeitianBeitian Compass QMC5883L AMP2.6/PIX4/PIXHAWK GNSS GPS GLONASS Dual Flight Control GPS Module BE-880Q BE-880 BN-880Q BN-880 BK-880 880Q (BK-880Q)
Main highlights- When the blue light flash, it means there is data output.
- Note: Please use the GPS module in an open place, the LED will flash after the satellite signal is found. Bad weather and indoor use will affect the accuracy of positioning
- If you have any issue when using our product,or you need product use documentation, please contact us directly for assistance.we will reply your problem in 24 hours.We try our best to provide the most professional seIrvice for each customer.
- Data Level : TTL or RS-232,Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
- Beitian 10th 9th 8th chip BE-880Q BE-880 BK-880 880Q BN-880Q BN-880 Compass QMC5883
8.3Good
View offer on:
Show more
9
DIATONEDiatone Mamba Mini BN-180 GPS Module M8 Plus
Main highlights- This small and lightweight GPS unit offers fast warm-startup and excellent accuracy.
- Suitable for CC3D, F3, F4, F7 Flight Controllers
- Data Protocol：NMEA-0183
8.2Good
View offer on:
Show more
10
GeekstoryGeekstory BE-180 GPS Module Beidou GPS AntennaTTL Level 38400bps for Arduino Raspberry Pi Aircraft Pixhawk APM Flight Controller
Main highlights- What you will get: 1*BE-180 GPS Module; 1*1.00mm 4pins Cable; 1* 20cm 1.0mm 4P Connector Male Cable
- This BE-180 GPS Module using the latest 10th generation chip When you use it for Raspberry Pi, there is no driver needed. Here is connection with RPi, red to 3.3v, black to gnd, green to txd, white to rxd
- This BE-180 GPS Module has Flash to save configuration, so you do not need to reset data next time when you use it.. Baud Rate : 4800bps to 921600bps, Default 38400bps
- The TX LED flash means gps module output normally. The PPS LED flash means gps module locate your place
- Data Level : TTL or RS-232, Default TTL level. To make it be RS232 output, you need to use one TTL to RS232 converter cable
8.0Good
View offer on:
Show more
Black Friday Sale
Deal ends in
HrsMinSec
Related deals you might like for beitian bn 180 gps
